RC Power FAQ

1) Beginner issues

A101	Why fly electric?
A102	How do I get started?
A103	What kind of planes can I fly with electric power?
A104	How do I sign up for the AMA/MAAC?
A105	What Kind of equipment do I need?
A106	What special tools would I need?
A107	Can you suggest a few beginner setups?
A108	Are soldered or crimp joints better?
A109	What goes on which stick?

2) Safety

A201	What safety procedures should I follow when flying?
A202	What is an arming switch?
A203	When should I use an arming switch?
A204	How much power will I lose? How much weight will I gain?
A205	What is a fuse? Why use one?
A206	What type of fuse should I use?
A207	How do I choose the fuse rating?
A208	How and where do I install the fuse?
A209	Are there any safety precautions for the motor battery?
A210	How do I fuse a brushless motor?

3) Batteries

A300	Battery Basics
A301	What's Volt, Amps, "C" rating, etc....?
A302	What are milli-amp hours?
A303	How fast can I charge my batteries?
A304	What is Nicad memory?
A305	What is Cell reversal?
A306	Should I cycle my packs?
A307	Can I deep discharge an individual cell safely?
A308	What is the discharge of a Nicad like?
A309	Black Wire Syndrome
A310	Low Tech Cell Matching
A311	What are the effects of series and parallel?
A312	What are NiMH batteries like?
A313	Can I use Lithium batteries for electric flight?
A314	What do the battery codes like SCR, AE mean?
A315	Is it safe to solder directly to batteries?

4) Electric motors

A401	What does "breaking-in" a motor actually do?
A402	How do I break-in a motor?
A403	What does gearing do?
A404	How do I compare an electric motor to an IC engine?
A405	What are motor constants?
A406	What's the difference between Delta and Wye Brushless Motors?
A407	What is "timing"?
A408	How much should I advance a speed 400?
A409	How do I use the "speed 400 timing tool?"
A410	How much heat can our motors dissipate?
A411	How can I keep my motors clean?
A412	What is a sensorless motor/controller?
A413	How does a sensorless motor work?
A414	What do the motor names (Speed 400,600, 05, 25) mean?
A415	How do I do a "Water break-in" ?
A416	How do I measure motor constants ?
A417	Will this cheap Mabuchi 540/380 etc. be good for E-Flight ?
A418	How many capacitors do I need on my motor and what values ?
A419	Should I wire two motors in series or parallel?
A420	Where can I find some information on common brushed motor constants?

5) Speed controllers (ESC's)

A501	How does a speed control work?
A502	What is the advantage of a High Rate Control?
A503	What is the best switching rate for a hi rate ESC?
A504	How does a motor brake work?
A505	What is a BEC and how does it relate to the speed control?
A506	What are the disadvantages of a BEC?
A507	What is a Cutoff?
A508	How long can I fly once the cutoff takes place?
A509	What is opto-isolation and what does it do?
A510	How do I disable the BEC on my speed control?
A511	Where does my BEC speed control plug in ?
A512	Can I control 2 brushless motors with one controller ?

6) Propellers

A601	Why doesn't my Graupner folding prop extend all the way out?

7) Chargers

A701	How does charging current relate to capacity?
A702	How can I make certain my packs are fully charged?
A703	How does a peak (or delta peak) charger work?
A704	Will my charger work with Ni-MH batteries?
A705	Will a NiCad peak charger work with Lithium batteries?

8) Model info

A801	What are the differences between Indoor, Slow and Park flyers?
A802	What are EDF models?
A803	What exactly are EPS/EPP/Depron and other construction foams ?
A804	What is the watts/pound rule?
A805	What does the Watt-hours/pound rule tell me?
A806	How do I match an electric power system to a given airframe?
A807	How do I convert a gas powered plane to electric?
A808	Are there any proven electric setups listed anywhere?

9) Electrical formulas

A901	How do I calculate duration?
A902	How do I calculate Watts?
A903	How do I convert units of measure?
A904	What is Orme's Law?

Reference resources
Mailing lists
FTP sites
Web pages
Newsgroups
Non-electronic Resources
Magazines
Books

Contributor Credits

What does the Watt-hours/pound rule tell me?

Q. What does the Watt-hours/pound rule tell me?
A. Jim Bourke

The rule is 5 Watt-hours per pound allows "good" performance with "good" duration.

We might want to ask: how does this airplane compare to that airplane in terms of performance. Maybe the two planes have the same watts/pound, but one of them can fly with performance for a lot longer. Why is that? You can use Watt-hours per pound to describe the energy density of your airplane. It is a measure of how much overall performance you will get. Almost all electric models out there are at around 5 watt-hours per pound. Extreme competition models might make 6 or even 7 watt-hours per pound. Many EDF's and other high performance airplanes with short durations are in the 4 watt-hour per pound category. This is not a measure of performance, by itself, but it is a measure of how long an airplane will perform at a certain level.

AULD competitions are largely determined by watt-hours per pound. Its an statement of how much energy is carried by the airplane for its weight.

The nice thing about watt-hours per pound is that it works regardless of what kind of cell is being used. We are getting to the point pretty soon where we may not be using NiCad's much longer. NiMH technology is coming on strong. Other cell types might present themselves soon. I can use this rule when planning out a model. If I know the plane will be 5 pounds, I will want at least 25 watt-hours. If I use 2000 mAH cells, I need 12.5 cells. If I use 1000 mAH cells, I need 25 cells. If I find some exotic cell that has a 4000 mAH rating, I only need about 6 of them to have the same overall power available to me during a given flight.